You are here:

Aidomes.com - Domes from American Ingenuity, Inc.

Panel Composition Print E-mail

American Ingenuity's

Component Panel's Composition

What are the American Ingenuity triangular and rectangular shaped panels made from? Center core of 7" Expanded Polystyrene R-28 Insulation (not Styrofoam!), exterior is ¾” thick steel reinforced concrete with interior of 1/2" Georgia-Pacific DensArmor Plus High-Performance gypsum wall board (which is moisture resistant, mold resistant gypsum and noncombustible).

The middle of each panel consists of a seven inch block of R-28 rigid expanded polystyrene (E.P.S.) insulation. The E.P.S. Insulation that Ai utilizes contains NO HBCD, NO TCPP, NO CFCs and NO formaldehyde and is not Styrofoam.   The EPS that Ai utilizes has a flame retardant added to it, therefore the EPS is noncombustible and is protected by the 1/2" DensArmor wallboard which is non-combustible and provides the Code required 15 minute thermal barrier. 

Your American Ingenuity concrete house kit is affordable and strong because it is engineered as a system of prefinished component panels. Each panel is cut at a computer-generated angle so that it fits flush with the adjacent panel. The edges are precisely beveled at the seams where steel mesh and concrete will unite to complete the structure.

Onsite the dome concrete building kit is assembled by:

  • erecting a temporary wooden rib system to support the triangle and riser panels during assembly
  • placing the panels one row at time using a hoisting mechanism - man lift
  • overlapping, locking and depressing the steel mesh between the panels
  • mixing concrete with mortar mixer following concrete recipe in the manual (Portland Cement Type III, masonry or stucco sand, fibers, liquid admixtures)
  • installing cables per blueprints
  • installing rebar around back of entryway panels, back of first floor door dormer panels, top of entryway panels & around first floor window dormer panels
  • form up and install beams or troughs around lip edge of entryway panels, first & second floor door dormer panels, channels in the entryway troughs
  • concreting the seams between the panels (5" wide and 3" deep) with two separate layers of concrete application using a bonding agent between the layers; And watering down all cured concrete before applying bonding agent or new concrete.
  • concreting the entryways, window dormers, door dormers, cupola and link with two layers of concrete. 
  • framing in the entryways and dormers and installing your locally purchased exterior doors and windows.
  • removing the temporary wooden rib system.  Return the steel hubs to receive a full deposit refund if returned during five month rental period and if all hubs are intact.

Onsite concrete is not applied over the pre-concreted component panels.  The interior shell wall board can be finished similar to conventional sheetrock with tape and joint compound. To view a panel and learn about Building Kit Assembly click on AssemblyAn Expanded Assembly Manual is now available with each new dome order.

To learn more about Hoisting Mechanisms click on Hoisting.  To learn more about entryways, dormers, etc. click on Building Options.

For Building Option Pricing click on Basic Kit Prices and then scroll down the page for the building options chart.  

American Ingenuity's Component Panel's steel mesh, concrete, EPS insulation and DensArmor wallboard contain no food source for mold growth and are therefore mold resistant.  The Georgia Pacific wallboard is not conventional sheet rock. Conventional sheet rock consists of  conventional gypsum and paper backing.  Sheet rock when it gets wet crumbles and molds.  The DensArmor gypsum when it gets wet does not crumble due to fiberglass reinforced core.  It has fiberglass backing on both sides. After the DensArmor dries out it goes back to its original firmness and consistency per the manufacturer.

Tell us more about American Ingenuity’s panel materials.

Concrete: The panel concrete is a special formulation containing synthetic fibers and liquid admixtures. Locally purchase bags of Portland cement and sand.  Mix the ingredients with a Mortar Mixer NOT a cement mixer!  Ai ships with your building kit the same fibers and admixtures that are used in the panel concrete so the seam concrete that is mixed on site will have the same properties as the panel concrete. These ingredients improve the concrete's characteristics, create super toughness, extend durability, give higher tensile and compressive strength, provide elasticity for expansion and improve freeze protection.  The first layer of seam concrete contains two liquid admixtures and synethic fibers.  The second layer does not require fibers; however now due to advances in fiber technology there are small 1/4" fibers that can now be added to the second layer.  These smaller fibers for the second layer can be purchased from Ai.

The concrete in your dome home out performs other exteriors because of its specially developed formula. Because of its exceptional composition, it actually gains strength over the years.

The exterior panel concrete, which is 3/4" thick, adheres directly to the steel mesh and E.P.S. insulation without the need of a bonding agent.  The panel concrete is hand applied, hand troweled, and hand sponged at American Ingenuity's Rockledge Florida factory.  However during the on site process of concreting the seams, entryways, dormers, etc., a bonding agent is applied on the first layer of concrete before the second layer is applied.  Bonding Agent is supplied with the kit with additional bonding agent being purchased from Ai. This bonding agent is not diluted onsite.  It is used full strength and must rest 30 minutes before new concrete can be applied over it.  Prior to applying bonding agent, water down cured concrete.  Before applying second layer of concrete, water down all cured concrete around where the new concrete will be applied.  The final layer of concrete is sponge float finished on site.

Steel: Galvanized steel wire mesh is encased in the concrete of each component panel and extends out over the insulation's beveled edges. As your dome panels are assembled, the mesh of each panel overlaps and is hooked to that of the adjacent panels with C-rings (commonly called "hog rings"). The dome then becomes completely encircled by steel mesh.

E.P.S. Insulation that Ai utilizes contains NO HBCD, NO TCPP, NO CFCs, NO formaldehyde.  The EPS thickness is 7" (R28).  The seven inches of sturdy, rigid R-28 expanded polystyrene (E.P.S.) insulation forms the core of each component panel. This is NOT Styrofoam!  The E.P.S. Ai uses is a closed cell with a 1 lb. per cubic foot density. The insulation is permanent, chemically and thermally stable; resistant to mildew; provides no nutritive value to animals, plants, microorganisms; non-irritating to skin.  The insulation will not rot, shrink, absorb moisture, compact, or deteriorate due to age or the weather. It also acts as a vapor barrier for your home, providing stable performance year after year. To learn more about E.P.S. as a Vapor Barrier click on Vapor Barrier.

ANALYSIS OF EXPANDED BEAD POLYSTYRENE

The Expanded Polystyrene (E.P.S.) Insulation that American Ingenuity utilizes is seven inches of sturdy, rigid R-28 modified E.P.S. insulation, which forms the core of each component panel. The E.P.S is one pound per cubic foot density (pcf).  EPS is NOT Styrofoam.

The E.P.S. insulation will not rot, shrink, absorb moisture, compact, or deteriorate due to age or weather. It also acts as a vapor barrier for your home, providing stable performance year after year.  The E.P.S. that American Ingenuity utilizes in its prefabricated panels:

  • is permanent
  • is chemically and thermally stable
  • is resistant to mildew
  • provides no nutritive value to animals, plants, microorganisms
  • is non-irritating to skin
  • contains NO Chlorofluorocarbon (CFCs) and is formaldehyde free
  •       Contains NO HBCD (hexabromocyclododecane) and NO TCPP (1-chloro-2-propyl) phosphate

What kind of vapor barrier will American Ingenuity dome have?  Approximately one quarter of the energy consumed by an air conditioner is used to extract water vapor from inside the house. Water vapor easily passes through most building materials and is readily swept into homes through joints, seams and through the attic. The E.P.S. insulation that Ai uses provides a good vapor barrier.   And the Ai building system provides for an air tight house.

During the US Dept of Energy Study on energy efficiency in  housing designs, the blower door test showed the American Ingenuity dome to be 56% tighter than the conventional test structure and 29% tighter than the Dow house.  To see if air was passing through walls of the dome, tests using infrared were performed. Thermal irregularities in the dome were shown to be insignificant.

Per the manufacturer of the E.P.S. which American Ingenuity uses, "the E.P.S. is closed cell and will not absorb more than 2.5% of water based on volume".  E.P.S. is often used as flotation for docks because it will not absorb water. 

Per E.P.S. manufacturer's data sheets the following description was given to explain how the E.P.S. is affected by Moisture:  "To retain their original insulation value, all insulation materials must remain dry.  Water is a good conductor of heat so a high moisture content in the insulation results in a significant loss of performance.  This is particularly so with fibrous materials which must be positively protected by an efficient vapor barrier.  Two ways in which moisture can affect insulation materials are; water absorption from contact with damp surfaces or rain penetration or from interstitial condensation of water vapor.  E.P.S. is a closed cell material and has minimal water absorption and low water vapor transmission.  Both of these properties are to a large extent, density related, but also to the degree of fusion of the material.  Tables 4 and 5 show typical performance figures for good quality E.P.S. boards manufactured to Arco Polymers recommendations.”           

Table 4  Water Absorption

Density (pcf)                                  1.0 lb                            1.5 lb                             2.0 lb
(pounds per cubic foot)

Water absorption (% vol)        less than 2.5                  less than 2.0                  less than 2.0

Table 5 Water Vapor Transmission (WVT)

Density (pcf)                                                     Grains (hr/sqft) In/Hg (Perm inch)

1.0                                                                                            1.2-2.2

2.0                                                                                            0.6-0.8

2.5                                                                                            0.5-0.7

3.0                                                                                            0.5-0.7

The amount that a material will breathe is measured in perms or sometimes perm inches.

 “Note: FHA requirements for perimeter insulation are that the original K value of the material must not increase by more than 15% after repeated wetting and drying cycles.  Tests have been carried out on nominal 1.0 pcf density E.P.S. with an original K value (at 75 degrees F) of 0.26.  After submersion the K value was found to be 0.28--an increase of only 7.7%.”

 Climatic Changes:  E.P.S. board has been used as an insulation material in various types of building structures for over 35 years in climatic conditions ranging from Arctic cold to desert heat and has performed satisfactorily.  E.P.S. does not become brittle at sub-zero temperatures (in fact its K value improves) and suffers no loss of impact resistance at -100 degrees F compared with 73 degrees F.  The maximum recommended continuous operating temperature is 175 degrees F.  Roof surface temperatures in Southern States may reach this temperature for short periods, but with suitably designed roof systems E.P.S. can be used under these conditions.”

In Ai's building system the water is stopped on the outside surface because the concrete is rich and dense enough to inhibit significant absorption and it is coated with a primer and two coats of good quality exterior concrete paint which further insures against leaks.  If a leak occurs the remedy is to check the area for hair line crack that gets repaired with elastomeric patching compound and another coat of paint.  If and when any water gets past the concrete very little will be absorbed by the E.P.S.

Now this brings up breathability of the E.P.S.  The amount that a material will breathe is measured in perms or sometimes perm inches.  E.P.S. will breathe enough to allow it to dry out inside our walls.  At the same time it is tight enough to also serve as a good vapor barrier. Ai’s insulating concrete panel (ICF) is made from expanded polystyrene (E.P.S.) molded into lightweight foam blocks. The foam itself provides excellent insulation with an R value of R-24. The R-value of E.P.S. remains constant. (R-values of traditional fiberglass insulation decreases when the material is wet or damaged.)  Ai chose to manufacture its dome component panels with Modified Expanded Polystyrene (E.P.S.) foam because of its fire performance, structural performance, and environmental advantages. Modified E.P.S. contains no formaldehydes, no CFCs, no HBCD, no TCPP or toxic chemicals, and uses fewer resources to manufacture than other insulation products.  E.P.S. provides you with superior thermal performance to better insulate your buildings, and no harmful CFC’s have ever been used to manufacture it.

You can now recycle your jobsite scrap through a network of manufacturers, re-processors, and retailers across the country. E.P.S. is a valuable resource than can be remanufactured into foam packaging or made into an amazing array of polystyrene products from office supplies to video cassette cartridges.  To locate your nearest E.P.S. collection site, call the RECYCLING HOTLINE at 1-800-944-8448.  Please recycle jobsite scrap.

Expanded Polystyrene (E.P.S.) Facts

The E.P.S. that American Ingenuity utilizes is manufactured from expandable polystyrene beads containing a hydrocarbon blowing agent and a flame-retardant additive that contains NO HBCD (hexabromocyclododecane) and NO TCPP (1-chloro-2-propyl) phosphate. Ai's insulation is made from Nova Chemicals M-77 E.P.S. product.

The EPS Ai utilizes is a closed cell, lightweight, resilient, foamed plastic composed of hydrogen and carbon atoms. There are two common types of polystyrene foam, Extruded Polystyrene or X.E.P.S. (Popularly known by its Dow trademark, Styrofoam) and Expanded Polystyrene (E.P.S.). American Ingenuity utilizes only Expanded Bead Polystyrene that contains NO HBCD, NO TCPP, NO CFC's and NO formaldehyde. Ai does not use Styrofoam.

During the processing of E.P.S., steam heat softens the beads and causes the blowing agent to expand to produce moisture-resistant multi-cellular particles, which increase in size up to 40 times their original volume.  Following a period of stabilization, during which time the beads lose their moisture, the blowing agent condenses out and air diffuses into their cellular structure, the pre-expanded beads are molded into blocks of insulation.

The benefits of E.P.S. thermal insulation products are its lightweight, has stable long-term thermal resistance, no R-value loss over time (Source: 1985 Study conducted by Structural Research, Inc. for NRCA, MRCA, and SPI), and cost effectiveness when compared to other rigid board insulations on the basis of R-value.

Is E.P.S. a water, vapor or air barrier?

E.P.S. is considered water resistant and vapor permeable and at the density and thickness that American Ingenuity utilizes, the material acts as both a vapor retarder and an air barrier. This characteristic essentially moves the dew point to the exterior side of the concrete wall, minimizing interior humidity in the summer, and at the same time eliminates air infiltration in all seasons which is recognized as a major cause of R-value loss in fiberglass insulation. Air exchangers or heat recovery ventilation systems are highly recommended!

Is E.P.S. foam toxic?

E.P.S. is an inert, non-biodegradable organic plastic foam which will not rot and is highly resistant to mildew. According to National Bureau of Standards Combustion Tests, data collected from seven labs concluded that under the worst case fire scenario, fumes from E.P.S. are no more toxic than those from wood (Douglas Fir).  

Is E.P.S. Flammable?

Due to the flame retardant added to the EPS during expansion, the EPS is not combustible but will melt and draw back from a heat source.  Tests have shown that the smoke and soot produced from the melting EPS is less than is produced by burning Douglas Fir wood.  Of course no one wants to breathe smoke or soot...that is why there are smoke detectors to alert occupants to fire.  The requirements of all the major code organizations for foam plastics is that they have a flame spread of not more than 75 and a smoke development rating of not more than 450. The foam used in Ai’s component panels has a flame spread rating of 15 and a smoke development rating of 125 based on ASTME84-87 tests, well below the code requirements.

If you are in an extremely cold climate (Canada) you may want to purchase 9" EPS R36 insulation.  Just remember if you purchase the thicker insulation, this will increase the size of the panels, which will cause the kit to need more trucks or more containers for delivery. To learn more about the properties of the E.P.S. click on E.P.S. data and then scroll down the page to Analysis of Expanded Bead Polystyrene.

1/2" Georgia Pacific DensArmor Plus Gypsum Wall Board

WallBoard: Consists of Georgia Pacific 1/2" DensArmor Plus High Performance Gypsum Panels adhered to the E.P.S. insulation with a wallboard adhesive. The core of the board is gypsum reinforced with fiberglass. DensArmor Plus High-Performance Interior Panels are noncombustible (as defined and tested in accordance with ASTM E136 or CAN/ULC S114) interior panels that consist of a moisture-resistant gypsum core with coated fiberglass mats. The fiberglass mats provide superior protection from incidental moisture. The core of DensArmor Plus panels is reinforced with fiberglass, increasing the product’s strength. The treated core and the coated facings made with fiberglass offer greater moisture resistance and improved dimensional stability than regular gypsum board. The product resists warping, rippling and buckling.

The DensArmor has zero flame spread and zero smoke development and complies with the 15 minute thermal barrier test as described in 2010 Florida State IRC Section R316.4.

Georgia Pacific's Dens-Deck roof board is a patented nonstructural glass mat-faced, noncombustible, water-resistant, gypsum core panel.  Georgia Pacific does not add any flame retardant to its gypsum products.  The DensArmor contains no HBCD and no TCPP.

Q: Does the interior shell wall board that American Ingenuity uses support the growth of mold?
A:
. DensArmor Plus Panels are highly resistant to the growth of mold, and have scored a 10, the highest level of performance for mold resistance under ASTM D3273 test method. DensArmor Plus Interior Panels are the first drywall panels to be GREENGUARD indoor Air Quality Certified and GREENGUARD Children & Schools Certified for low emissions of volatile organic compounds (VOCs) by a leading third-party organization, GREENGUARD Environmental Institute.  In addition, DensArmor Plus interior Panels are the first drywall panels listed as GREENGUARD microbial resistant.  This listing means Dens-Armor Plus Panels, which feature fiberglass mats instead of paper facings used on the surface of traditional gypsum board products, resist mold growth.  The microbial resistant test is based on ASTM D6329, a testing standard set by ASTM International, which develops testing guidelines and procedures for building materials, products, systems, and services.

Green, brown or black algae can appear on the wallboard. Algae just needs water and sunlight to grow.  Algae can be removed with a combination of chlorine and water.

The wallboard is adhered to the EPS with a wallboard adhesive.  The glass mats embedded into the core on both faces, results in dimensional stability and prevents warping. The glass mat is encapsulated with a coating which reduces skin irritation from exposed glass fibers.

Fire Protection: Per Georgia Pacific:
  • 1/2" Dens Armor Plus High Performance Gypsum Panels are gypsum panel products, designed for interior use, are manufactured to meet the temperature rise criteria of a thermal barrier as described in Section R316.4 of the 2010 Florida Residential Building Code.
  • In addition to having a non-combustible core per ASTM E 136, Dens Armor Plus has been evaluated by Underwriters Laboratories LLC per UL 723 Standard for Test for Surface Burning Characteristics of Building Materials. DensArmor Plus has a Flame spread/Smoke Development of 0/0.
  • The Finish Rating Thermocouple Temperatures obtained during the evaluation (WFCI Project No. 06047A) was conducted at Western Fire Center (WFCi) in Kelso, WA. WFCI is a recognized testing facility per the Gypsum Association (GA-600).
  • The Finish or Membrane Protection Rating was determined to be 0.15:40 for 1/2" DAP. Please note the average ambient temperture was 21.0 degrees C for the 5 Finish Rating Thermocouples.
  • Properties of Dens-Armor: Noncombustible, Water Resistance, Dimensional Stability, Decay Resistance, Resistant to Warping, Rodent and Fungus Resistance, Torch Safe, High Compressive Strength.
The wallboard seams can be finished similar to drywall by applying joint compound and tape on the seams and painting the wall board. To blend the seams, mix some vermiculite into your paint.  Or joint compound can be skip troweled over the wallboard before priming and painting.

 If I am not ready to assemble my dome immediately, can it sit out outside? Yes, however if you expect to have your kit outside for more than two to three months, when you order your kit request that the E.P.S. edges be painted. The dome kit should not sit outside in the winter.  Call us for details at 321-639-8777.

What do the component panels weight?

Dome Diameters 22' 27' 30' 34' 40' 45' 48'
Triangular (lbs)

155-180

245-295

120-150

160-200

205-250

230-275

275-355

Riser (lbs)

255

315

230

260

280

315

350

 How are the panels supported during assembly?  Ai recommends using the temporary "wooden rib system." The rib system consists of your own 2x4's (cut to length and holes drilled to our specs) and steel hubs on loan from American Ingenuity to erect a free standing geodesic framework. The 2x4's can be purchased from Ai (precut, holes drilled with ends painted) and shipped on the truck with your kit. The deposit on the hubs is $800 for a 5 month rental time...$20 a month rental thereafter, with the client paying to ship the hubs back to Ai to receive their deposit back less any additional months rental and any cost for any missing or damaged hubs. The bolts/nuts/washers are purchased for $100 and are not returned to Ai.  An Expanded Assembly Manual is now available with each new dome order.

The "Rib System" dictates the exact panel placement. Once all the seams/options have been concreted and entryways/dormers framed in the "Rib System" is removed and recycled into the interior framing and the hubs returned to us. Click on Radial to learn more. Click on Rib to learn more.

How are the panels hoisted into place? And what equipment is attached to the panels to make lifting easier?

  • The typical method for lifting the panels is by man lift, crane or transverse fork lift.
  • Monthly rentals on transverse lifts also called Boom Lifts, Horizontal Boom Fork Lifts, Roofing Lifts, Shooters are available from National Rental Chains.
  • Four Panel Lifting Spikes can be purchased from Ai for $100.  To learn more about the spikes click on Lifting Spikes.  Please scroll down the page to find the spikes info.

How long does it take to assemble the dome shell kit if I use the Kit Assembly Specialist? Depending on the size dome, and if your building kit has two entryways and four dormers with dome built on concrete slab, the shell assembly with one layer of concrete in the panel seams and on the entryways and dormers can take about 9 to 16 days. Assembly time depends on the number of workers in your team, your foundation type, weather and the type of hoisting mechanism. Click on Kit Assembly Specialist to learn more.

 

Main Menu